home
|
products
|
accessories
|
Accessories
Product Descriptions
|
A-3000WB ADHESIVE
A-3000WB Adhesive is a water-based latex adhesive used primarily to
secure the Volclay Swelltite membrane in both vertical and horizontal
applications. The product is VOC compliant and changes from a light
gray to dark gray upon application. Waterproofing membrane is installed
to adhesive after it turns to dark gray color. Product should be stored
in dry, warm conditions and should not be allowed to freeze prior to
use.
Product packaging: 5-gallon (18.9 l)
pails. |
  |
|
|
|
BENTOSEAL®
Bentoseal is a trowel-grade bentonite based mastic that is used
with Volclay bentonite waterproofing systems to detail at membrane
terminations, around penetrations, over grouted concrete form-tie
holes, and provide fillets to inside wall corners. Unlike most mastics,
this premium mastic is capable of swelling and self-sealing upon
hydration and is VOC compliant. Bentoseal can be covered with a
waterproofing membrane immediately after application. Bentoseal is not
designed for split-slab deck construction; use M-2000 Liquid Flashing
for deck work.
Product packaging: 3-gallon (XXX l)
pails. |
 |
|
|
|
CETSEAL
CETSEAL is a multi-purpose, single component polyether moisture cure sealant/adhesive. CETSEAL is a low VOC, 100% solids, non-shrinking
product with excellent UV resistance.
Product packaging: 10.1 oz cartridges - 12 cartridges per case. Typical weight per case: 12 lbs (5.4 kg)
20 oz foil packs - 12 foil packs per case. Typical weight per case: 20 lbs (9 kg |
|
|
|
|
GF-40SA
GF-40SA is a 40 mil (1 mm) thick self-adhering thermoplastic flashing membrane with excellent UV, tear, and puncture resistance. GF-40SA is produced with 60% post industrial recycled content by weight and is resistant to most forms of fungus, algae, and microbiological attack.
GF-40SA is used for above and below grade flashing applications including grade terminations, parapet walls, curbs, and thru-wall flashing. GF-40SA can be used in conditions exposed to direct UV and weather conditions.
Product packaging: Available in 18” x 50’ (0.5 m x 15.2 m) rolls; two rolls per box. |
|
|
|
|
HYDROBAR® TUBES
Hydrobar Tubes are 2” (50 mm) diameter by 2 foot long (600 mm)
tubes of Volclay granular bentonite encapsulated in a water-soluble
film tube. Hydrobar Tubes are a convenient means of providing extra
waterproofing protection at the critical wall to footing intersection
joint. When used with Ultraseal or Voltex membranes, the tubes are
installed prior to the membrane directly against the wall at the base
corner. When used with Volclay panels, the tubes are installed after
the Panel installation directly in the wall base corner.
Product packaging: 16 tubes per box
for 32 linear feet (9.75 m). |
 |
|
|
|
M-2000 LIQUID MASTIC
M-2000 Liquid Mastic is a single-component, trowel-grade moisture
cure polyurethane mastic that is used with Volclay bentonite
waterproofing systems to detail primarily at membrane terminations,
around horizontal deck penetrations and transitions, over grouted
concrete form-tie holes, and provide fillets to inside wall corners.
Product typically requires a minimum 12 hour setting time prior to
being covered by a waterproofing membrane.
Product packaging: 5-gallon (18.9 l)
pails. |
 |
|
|
|
VOLCLAY® SEAMTAPE
Volclay Seamtape is a thick premium butyl rubber tape primarily
used to seal Volclay Ultraseal BT and Swelltite membrane overlap seams where the
inherent adhesive face of the tape seals the membrane liner face.
Seamtape provides membrane protection from inclement weather prior to
backfill or concrete placement, as well as, enhances the performance of
the waterproofing system during service. Its outstanding conformability
allows the tape to be easily installed on irregular surface conditions.
Product packaging: 2” (50 mm) x
125-ft (38 m) roll; 6 rolls per box. |
 |
|
|
|
TB-BOOT
TB-Boots are specially designed tieback covers used to maintain waterproofing integrity at soil retention tieback heads. TB-Boot is a single piece, durable pre-formed thermoplastic cover that provides a simple and quick waterproofing installation detail. TB-Boots are used with various CETCO waterproofing membrane systems including Voltex, Ultraseal and CoreFlex.
The specially designed tieback cover incorporates a 3-dimensional pre-formed shape to accommodate most tie-back heads installed at varies angles and its angled shape is designed to displace a minimal amount of concrete. The thick thermoplastic construction provides the strength and durability to withstand the concrete placement. TB-Boot is available in three sizes to accommodate various tie-back head sizes. Each size is also available with a gray thermoplastic membrane flange to weld CoreFlex membrane.
Available sizes:
THREE TB-BOOT SIZES: TB-6SN is 6” (150 mm) deep, TB-8 is 8” (200 mm) deep, and TB-10 is 10” (250 mm) deep.
Each size is also available with gray weldable flange for CoreFlex: TB-6SNF, TB-8F and TB-10F.
|
 |
|
|
|
VOLCLAY® WATERSTOPPAGE
Waterstoppage is chemically
treated granular bentonite used as a detailing accessory product with
Volclay Waterproofing Systems. When wetted, Waterstoppage forms a
dense, low permeable material that combines with the bentonite in the
Volclay membranes to form a seamless waterproofing system. Typical
application is around slab penetrations, pile caps, and grade beams
prior to the waterproofing membrane installation. Waterstoppage is also
applied to the roof deck of tunnels and earth covered structures prior
to Voltex and Voltex DS installation.
Product packaging: 50-lb bags (22.6 kg).
|
 |
|
|
|